DIN BAR MOUNTED
Take a look at our range of Din bar mounted Controllers.
If you need help selecting your controller or need a custom design system, Contact us.
DIN Rail Mounted Level Controller – Electroprobe Z
DIN Rail Mounted Level Controller – Sensitivity Options – Electroprobe Q
DIN Rail Mounted Level Controller – Sensopress
DIN Rail Mounted Level Controller with Adjustable Sensitivity and Time Delay – Electroprobe EV
DIN Rail Mounted Level Controller with Alarms – Electroprobe DB
DIN Rail Mounted Pump Sequencer 3
DIN Rail Mounted Pump Sequencer 2q
DIN Rail Mounted Pump Sequencer 2
DIN Rail Mounted Pump Sequencer
DIN Rail Mounted Rainwater Level Controller – RainControl
Voltage Control – 3F Control
DIN Rail Mounted Level Controller – Electroprobe Z
DIN rail mounted (2DIN, 35mm) conductivity probe level. Available for various supply voltages from 12 to 415Vac.
Single or Double Voltage Supply (Z8 or Z11 models).
Models available with Octal or Undecal DIN Sockets, can be replaced in seconds.
DIN rail mounted (2DIN, 35mm) conductivity probe level controller. Available for various supply voltages from 12 to 415Vac.
Electroprobe Z is a multifunctional level controller with 1 fixed function. The Differential Fill/Drain Function, activates a relay output to maintain the level between two probes set at different heights. The relay only changes state when either the upper probe becomes immersed or the lower probe becomes dry, allowing the water level to move between but not exceed the area between the two level probes.
3 conductivity probes are used, a common electrode is always immersed and 2 electrodes above this level form low and high set points allowing Electroprobe Z to maintain a the level within a specific range.
Electroprobe Z is commonly used with water and other fluids with dependable conductivity, there are 3 main models available.
NS – Standard Sensitivity – For clean water and fluids with a maximum total resistance of 5.6KΩ. This unit will tolerate very long probe cable lengths of up to 1000m.
AS – High Sensitivity – For fluids with low conductivity, particularly rainwater, with total resistance of 68KΩ.resistance of 68KΩ. This Model will tolerate probe cable lengths of up to 80m.
SR – Adjustable Sensitivity – For fluids of unknown resistance. Adjustable between 0 and 100KΩ.This Model will tolerate probe cable lengths of up to 70m.DIN Rail Mounted Level Controller – Sensitivity Options – Electroprobe Q
DIN rail mounted (3DIN, 54mm) conductivity probe level controller.
Available for various supply voltages from 12 to 415V AC and DC.
DIN rail mounted (3DIN, 54mm) conductivity probe level controller. Available for various supply voltages from 12 to 415V AC and DC.
Mac3 Electroprobe Q is a multifunctional level controller with 1 fixed function. The Differential Fill/Drain Function, activates a relay output to maintain the level between two probes set at different heights. The relay only changes state when either the upper probe becomes immersed or the lower probe becomes dry, allowing the water level to move between but not exceed the area between the two level probes.
3 conductivity probes are used, a common electrode is always immersed and 2 electrodes above this level form low and high set points allowing Electroprobe Q to maintain a the level within a specific range.
Electroprobe Q is commonly used with water and other fluids with dependable conductivity, there are 3 main models available:
NS – Normal Sensitivity – For clean water and fluids with a maximum total resistance of 5.6KΩ. This unit will tolerate very long probe cable lengths of up to 1000m.
AS – High Sensitivity – For fluids with low conductivity, particularly rainwater, with total resistance of 68KΩ.
SR – Adjustable Sensitivity – For fluids of unknown resistance. Adjustable between 0 and 100KΩ.DIN Rail Mounted Level Controller – Sensopress
Mac3 Sensopress is a programmable, DIN rail mounted level controller and is ideal for integration with OEM and panel built products.
For use in Clean Water or Liquid Food Products.
Mac3 Sensopress is a programmable, DIN rail mounted level controller and is ideal for integration with OEM and panel built products.
Sensopress measures the level of liquid in a tank or reservoir using a high accurate pressure sensor which detects the weight of fluid above it. Pumps and valves can be controlled to fill, empty or maintain levels by Sensopress based on the reading of a single sensor with no mechanical movement.
Sensopress avoids the need for technicians to accurately set floats or sensors at various heights within the tank in order to operate pumps and valves at the right levels. All levels and functions can be precisely set from the control panel.
Sensopress can function with any liquid using a probe and can be manually calibrated to accept probes of different ranges.
Sensopress is available in single channel and multi-channel models. The single channel model is supplied with a single output for controlling one external appliance, whereas the multi-channel is supplied with 4 outputs.
Each output channel operates independently and may overlap in range.DIN Rail Mounted Level Controller with Adjustable Sensitivity and Time Delay – Electroprobe EV
DIN rail mounted (4DIN, 76mm) conductivity probe level controller with adjustable sensitivity and time delay.
Available for various supply voltages from 24, 117 and 230V AC.
DIN rail mounted (4DIN, 76mm) conductivity probe level controller with adjustable sensitivity and time delay. Available for various supply voltages from 12 to 415V AC and DC.
Mac3 Electroprobe EV is a family of DIN rail mounted level controllers. Electroprobe EV operates between 2 level probes set at different levels within the tank, plus a common probe (always immersed). The output relay is activated when water touches the upper probe, and de-activated when the lower probe becomes dry. Below both these probes a common probe provides a constant sensing connection back to the controller.
The following features are available in various models of Electroprobe EV:
Differential Fill/Drain function – Activates a relay output to maintain the level between 2 probes set at different heights.
Adjustable Sensitivity up to 100Kohm, suitable for water of low conductivity such as rainwater.DIN Rail Mounted Level Controller with Alarms – Electroprobe DB
DIN rail mounted (4DIN, 76mm) conductivity probe level controller with external alarm relay.
Available for various supply voltages from 24Vac, 117Vac and 230Vac.
DIN rail mounted (4DIN, 76mm) conductivity probe level controller with external alarm relay. Available for various supply voltages from 24Vac, 117Vac and 230Vac.
Mac3 Electroprobe DB is a multifunctional level controller with 4 functions:
Differential Fill/Drain Function, activates a relay output to maintain the level between two probes set at different heights. The relay only changes state when either the upper probe becomes immersed or the lower probe becomes dry, allowing the water level to move between but not exceed the area between the two level probes.
High Level Alarm – Activates the alarm relay when a probe is immersed.
Low Level Alarm – Activates the alarm relay when a probe becomes dry.
Single Point Control – Switches a 2nd control relay when a probe is immersed or dry. This can be used to inhibit/enable the device attached to the differential relay, or to enable an additional device.DIN Rail Mounted Pump Sequencer 3
Mac3 Sequencer is a DIN rail mounted device which balances the run-time of 2 or 3 pumps in a duty standby/assist configuration depending on model.
Pumps are alternated during normal usage, but allows the controller to activate both pumps together if there is a sudden demand.
Sequencer 3 – Advanced version of the sequencer that drives groups up to 3 pumps. Interface with LED’s and control buttons.DIN Rail Mounted Pump Sequencer 2q
Mac3 Sequencer is a DIN rail mounted device which balances the run-time of 2 or 3 pumps in a duty standby/assist configuration depending on model.
Pumps are alternated during normal usage, but allows the controller to activate both pumps together if there is a sudden demand.
Sequencer 2q – It has the same characteristics and functions as the sequencer with the addition of a panel containing two switches for pump operation and seven LED diodes that always show the system status.DIN Rail Mounted Pump Sequencer 2
Mac3 Sequencer is a DIN rail mounted device which balances the run-time of 2 or 3 pumps in a duty standby/assist configuration depending on model.
Pumps are alternated during normal usage, but allows the controller to activate both pumps together if there is a sudden demand.
Sequencer 2 – Is has the same characteristics and functionality as the sequencer with the added LED’s for visualising faults.DIN Rail Mounted Pump Sequencer
Mac3 Sequencer is a DIN rail mounted device which balances the run-time of 2 or 3 pumps in a duty standby/assist configuration depending on model. Pumps are alternated during normal usage, but allows the controller to activate both pumps together if there is a sudden demand.
Sequencer – In rail mounted device which balances the run-time or 2 pumps in a duty-standby/assist configuration.DIN Rail Mounted Rainwater Level Controller – RainControl
DIN rail mounted unit, that measures a rainwater tank level using a submerged pressure sensor (not included) and either tops up with a measured amount of mains water (direct systems with submerged pump), or opens a 3 way motorized valve (indoor break tank & pump systems) when required.
When a low level threshold is reached, RainControl opens a solenoid or motorised valve to supply mains water until a high level threshold is reached. After this, RainControl de-activates the output and reverts to level display mode.Voltage Control – 3F Control
The Mac3 3F Controls are a DIN socket mounted single phase, adjustable under-voltage monitoring and protection relays intended for use in control panels.
Mod.22 is Single Phase.
Mod.33 is three phase with additional phase loss protection.